Willys MB 404620 1-9-45 'Calsat'

If you have an unrestored WWII jeep, we would like to see pictures, and hear your comments. NO EBAY or COMMERCIAL SALES.
User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Thu Jul 30, 2020 5:52 am

I was going to start a new thread over on the General Discussion board, as this Jeep is no longer an Unrestored Original. However, without posting all the 'so far' pictures the project continuity will be lost, and there seem to be a good number of restoration threads on here, so I'm going to stay. The mods are very welcome to move the whole thread over if they wish.

To recap, I bought the Jeep in France back in 2012 when the original photographs were taken, but until a couple of years back I didn't have time to get to grips with it, and it languished, at times out in the elements. It became very clear that this was not going to be a 'maintain originality' project as I had wished, but a full restoration.
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
twinflyer17
G-Colonel
G-Colonel
Posts: 1241
Joined: Thu Sep 12, 2013 12:49 pm
Location: Aberdeen, MD

Re: Willys MB 404620 1-9-45 'Calsat'

Post by twinflyer17 » Thu Jul 30, 2020 6:07 am

Toby, great looking jeep and I'm looking forward to following your progress!
Sean

GPW 108175 viewtopic.php?t=267732
DOD 4/14/43 Louisville, KY USA20371070

MVPA
AOPA

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Thu Jul 30, 2020 6:09 am

Removal of the tub and motor revealed another setback, one which I had long suspected;

Image

And this is why;

Image
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Fri Jul 31, 2020 5:50 am

I sandblasted the chassis and axles, put them into primer, and set them aside. This was last autumn. The chassis will be going to http://www.chassisalignment.co.uk/ to be straightened. They seem to be able work miracles, even on enormous truck chassis. Their website is well worth a look.
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Fri Jul 31, 2020 8:57 am

At about the same time I started to strip the bonnet. It is from a GPW, and had a large star with the gas vesicant paint insert. No trace of any numbers.

Image

Image

Image
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Sat Aug 01, 2020 3:24 am

Again, put away for the winter. There's a bit of metal shrinking to do in the areas that have been filled, and I've replaced the damaged cowl end of the hinge from one salvaged from another hood. I should probably swap it for an MB hood, but it will do for now.
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Sat Aug 01, 2020 4:14 am

A couple of months ago I turned my attention to the tub. There's a lot of work to do, and I realised early on that the rear floor is too beaten up to rescue, as is the driver's side rear wheelhouse. It will need a rear panel as well.

I took some photos to record the course of the radio cable and one or two other things.

Image

Image

Image

Image

Image

Image
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Sun Aug 02, 2020 3:36 am

My first move was to investigate and cut out a couple of nasty patches on the floor and the side in the area of the radio box, itself long gone. I suspect this is a common problem, where water and dirt get caught behind and under the box.

Image

Image

Image

It seems strange that the patches seem to have been made of beaten up old sections of sheet, which then had to be painstakingly filled and rubbed back. Surely quicker and better to use a decent section of sheet, and save yourself all that trouble.
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

User avatar
horrocks
G-Colonel
G-Colonel
Posts: 1724
Joined: Fri Aug 31, 2007 1:34 pm
Location: Ongar, England

Re: Willys MB 404620 1-9-45 'Calsat'

Post by horrocks » Sun Aug 02, 2020 6:57 am

I next turned my attention to the passenger-side rear wheel housing. This was the least damaged of the two, and I wanted to try to shrink the metal on the top surface back. I wasn't that optimistic, as I've had no luck trying this in the past. I used a combination of heat/wet cloth and hammer and dolly, and a shrinking disc.

Image

Image

I had some success with the shrinking disc on more localised creases, bringing them out quite successfully, but no progress at all with the heat/hammer/dolly, in fact I ended up stretching the metal even more. I was taking a lot of time going nowhere. Given that the seam between the wheelhouse riser and the top had also been roughly welded up, and I just wasn't going to have the available time to learn how to shrink the metal properly, I decided to cut the top of the housing out and replace it. I had actually bought new sections from Jeep Sud Est when I collected the Jeep back in 2012.

Image

Image

Image

Image

Image

Image
Toby

Willys MB 3/13/42 127415
Willys MB 1/9/45 404620

Post Reply

Return to “Original Unrestored WWII Jeeps”

Who is online

Users browsing this forum: No registered users and 3 guests