Page 1 of 1

New Mule with SN's

Posted: Thu Jun 06, 2019 12:03 am
by Guam0311
I just recently picked up another MULE which will add hours of fun and work as well as emptying the bank account.

I know Chuck, Charles and others on here may want the numbers from the data plates to add to their data base. I was surprised that the plates were still there. Maybe the previous owner submitted the SN's but here they are anyway. The Mule is an A-2 but it has straight drop gear axle covers in the rear so I guess someone converted a 4 wheel to a 2 wheel? I presume the bed and drop gear housings are magnesium? The Mule has no motor or fuel tank.

Manufacturers SN: BMY 762
REG # 314859
Delivery Date: 02-66
Model: M274-A2
MFR PN: 6736605
Contract Number: PA-20713 AMC-03624 (T). The 713 could be a 113. hard to read
IMG_0456.jpg
IMG_0456.jpg (144.54 KiB) Viewed 2501 times

Re: New Mule with SN's

Posted: Thu Jun 06, 2019 9:38 am
by Chuck W.
Thanks for sharing your numbers. Contract number should be DA-20-113-AMC-03624(T)

I will look and see what I have left, I may have the front cross member intake pipe and the steering column brace, if you are interested.

Re: New Mule with SN's

Posted: Thu Jun 06, 2019 10:04 am
by muleman7
Look on the side of the transmission drivers side for the 4ea studs that retain the rear bell crank assy if it is smooth and no studs then my guess is someone installed an A5 trans axle into you A2 to complete or fix a non functioning A2 trans.

It can be drilled and tapped for 4WS this is my way of locating and drilling and tapping.

Caution: the top left hole can only be drilled about 3/4" deep otherwise you may drill into the reverse idler gear and snap off your drill bit that will now be in the transmission.

Marking for the 1st mounting hole

Image

Drilling and tapping the first hole

Image

Image

Installing 1st stud and secured with red lock-tite

Image

Image

Ready to Drill the other 3 hole using a drill guide

Image

1 Stud installed and the other 3 holes drilled ready to tap

Image

Using a tap guide I insert a bolt that is turned down to 5/16" to align the guide for tapping the other 2 holes then inset a bolt into one of the tapped hole and tap the 3rd hole. Then I remove the tap guide and use a bottom tap to finish.

Image

Image

Image

Image

Image

Rear Bell Crank installed waiting for 3ea nuts and LWs

Image

Re: New Mule with SN's

Posted: Thu Jun 06, 2019 10:39 pm
by m37-man
Is this the Mule "trailer" that was in the Julian area?

There are several Mule owners in the SD area if you are local and need free advice.

Re: New Mule with SN's

Posted: Fri Jun 07, 2019 1:24 pm
by Mulemac02
So how can we see the mule data base on SN?

Sent from my SM-G955U using Tapatalk


Re: New Mule with SN's

Posted: Fri Jun 07, 2019 6:22 pm
by abbylind
Mine was built in 66 too. It was an A2 converted to an A5. I think Charles told me a lot of A2s were converted to A5s (Safety issue) I still have the studs on the rear axle for the AWS bell crank. I'd like to convert it back to AWS. Those tires look like they are aircraft related. Tow bar is a nice bonus.

Re: New Mule with SN's

Posted: Fri Jun 07, 2019 8:04 pm
by tga
We have a few take out engines if you need one. arvintga(at)gmail(dot)com or 309-242-45zero1.
IMG_2602.JPG
IMG_2602.JPG (142.46 KiB) Viewed 2388 times

Re: New Mule with SN's

Posted: Sat Jun 08, 2019 6:26 am
by Guam0311
Chuck W. wrote:
Thu Jun 06, 2019 9:38 am
Thanks for sharing your numbers. Contract number should be DA-20-113-AMC-03624(T)

I will look and see what I have left, I may have the front cross member intake pipe and the steering column brace, if you are interested.
Thanks Chuck, I am going to look over the mule and see what it all needs.

Re: New Mule with SN's

Posted: Sat Jun 08, 2019 6:40 am
by Guam0311
Charles, After looking at the Transmission left side, all 4 studs are there equipped and ready for the rear bell crank. That's a great tutorial and pictures of bell crank install. Thanks. Not sure if im going to make it four wheel. This one will be doing all the grunt work, worker MULE. definitely need new tires though.

Re: New Mule with SN's

Posted: Sat Jun 08, 2019 6:51 am
by Guam0311
m37-man wrote:
Thu Jun 06, 2019 10:39 pm
Is this the Mule "trailer" that was in the Julian area?

There are several Mule owners in the SD area if you are local and need free advice.

M37-man, yes this is the Mule from Julian Ca. Me and my son drove down from Northern Ca, Yuba City area and picked it up last week. Thanks for the help though. I used to live down there by Lemon Grove. It looks like the Mule was working on an Apple orchard perhaps? I know Julian is known for that.

Re: New Mule with SN's

Posted: Sat Jun 08, 2019 7:00 am
by Guam0311
Mulemac02 wrote:
Fri Jun 07, 2019 1:24 pm
So how can we see the mule data base on SN?

Sent from my SM-G955U using Tapatalk
I think they collect SN's over the years and use that info to breakdown the history of each MULE? for example who manufactured it. This MULE was made by Bowen McLaughlin York. Which I believe made all the A-2 models. Check with Chuck and Charles they will know.

Re: New Mule with SN's

Posted: Sat Jun 08, 2019 7:07 am
by Guam0311
abbylind wrote:
Fri Jun 07, 2019 6:22 pm
Mine was built in 66 too. It was an A2 converted to an A5. I think Charles told me a lot of A2s were converted to A5s (Safety issue) I still have the studs on the rear axle for the AWS bell crank. I'd like to convert it back to AWS. Those tires look like they are aircraft related. Tow bar is a nice bonus.
Yours is 66 also, what month? This mule also has the rear bell crank studs but rear straight cv axles. strange huh? The mule was used for working and was pulled by another mule, so I guess no need for the military tires, just the smooth. Now maybe just a street drag racer! yea those tow bars are pricey on ebay and other sites.

Re: New Mule with SN's

Posted: Sat Jun 08, 2019 7:17 am
by Guam0311
tga wrote:
Fri Jun 07, 2019 8:04 pm
We have a few take out engines if you need one. arvintga(at)gmail(dot)com or 309-242-45zero1. IMG_2602.JPG
Thanks TGA, yes I will be looking for an engine soon, not sure if to go Genset, but then I have to piece all the different parts together, engine shields, flywheel, etc,etc, just about everything, or a straight up MULE motor would be excellent. or rebuild a motor and piece together. aww the choices huh.

Re: New Mule with SN's

Posted: Sun Jun 09, 2019 4:58 pm
by abbylind
I checked the data plate.... 3-66