**Reduced 10K**Navy Landing Craft Conversion- For Sale

Ships, Boats, Small Craft, Patrol Craft, Landing Craft, Amphibious Tracked Military Vehicles, Wanted, For Sale (NO AUCTION or EBAY) and Knowledge Base
Post Reply
jmahoney266
G-Private
G-Private
Posts: 3
Joined: Sat Aug 22, 2015 1:39 pm

**Reduced 10K**Navy Landing Craft Conversion- For Sale

Post by jmahoney266 » Thu Feb 08, 2018 10:57 am

One Of A Kind
Waterfront condo? Excellent work boat opportunity

Retired Navy Landing Craft LCM-5 Conversion (closer to Pilothouse Trawler now)

Type: Workboat/Recreational Landing Craft
Make: Marinette Marine
LOA: 50 Feet
Beam: 14 feet
Draft: 26 inches
Bottom: Flat, Recessed Props, no keel.
Props: 28" 3-blade Brass on 2.5" SS drive shafts
Hull: 3/16" and 1/4" steel plate
Deck and Superstructure: 3/16" steel plate
Bulkheads: 3- Forward, Amidship and Aft, w/watertight doors.
Engines: 8V71-N Detroit 2-stroke Diesel Engines 400hrs Starboard, 4000 hrs Port
Transmission: Allison Marine M15LH
Fuel Cap.: Steel Tanks, 500 gal. Fuel (2x250)
Hydraulic Controls
21KW Kubota Generator -Diesel

This vessel has been our recreational liveaboard for the last 5 years on the west coast of Florida. Prior to us, she was a waterfront condo for about 4 yrs.. She is currently 2 bedroom, stacking washer/dryer, dishwasher, stove and oven. 2 cold roof air units, and portable A/C below deck. Some plumbing for heads but not completed. She is a project which can be completed by new owner or contract some of the welding out.
Her maiden voyage as recreational vessel, under her own power, was moving from downtown to the beach...served us well as a nice dwelling at Matanzas Pass Bridge with a million dollar view. At 40 Tons, she is very stable. Flat bottom with a 26" draft... We decided to have the bottom inspected and repairs completed. She was taken to Glades Boat Storage, under her own power. The bottom was last done about 13 years ago. It needs the bottom refurbished and amenities completed. Some repairs are completed. Glades allows owners to perform their own repairs and can stay on her while the project is being completed. A coat of Corroseal primer is being used to seal off rust. Have been welding on the hull, where she currently is on blocks. Most of the equipment/tools for the repair go with this boat. Health issues are keeping me from completing. My loss is your gain. Wire-feed Welder, grinders, Air tools and 60gl compressor included.
Would make a great mobile workboat, suited us well as liveaboard in a local marina.
Asking $25,000 as is, where is...Bring all offers. Will entertain a possible trade to a downsized trawler. Thanks for looking.
More Photos are available upon request...
Contact info: 239-223-5004
*One of a Kind:*
Last edited by jmahoney266 on Tue Mar 20, 2018 11:23 am, edited 3 times in total.

jmahoney266
G-Private
G-Private
Posts: 3
Joined: Sat Aug 22, 2015 1:39 pm

Re: Navy Landing Craft Conversion- For Sale

Post by jmahoney266 » Sun Feb 18, 2018 10:35 am

All the tools for project completion will stay with her. Please take a look. Lots of Character....

https://1drv.ms/a/s!AlFMIp-09SyQy1BxCc79rgsfrOXB

http://www.gladesboatstorage.com/

jmahoney266
G-Private
G-Private
Posts: 3
Joined: Sat Aug 22, 2015 1:39 pm

Re: Navy Landing Craft Conversion- For Sale

Post by jmahoney266 » Wed Feb 21, 2018 12:19 pm

She was being used as a waterfront condo. We got the engines going and took her to Ft Myers Beach as a Comfortable Liveaboard. When the bottom needed repairs, we drove her to Glades. When the bottom is completed, she can be splashed and the rest of project completed wherever you take her, while afloat..

Post Reply

Return to “Boats, Ships, Landing Craft, and Tracked amphibian”

Who is online

Users browsing this forum: No registered users and 7 guests