What is this wrench for any ideas??

RedArrow2016 · Post by **RedArrow2016** » Fri Nov 02, 2018 9:30 pm

Does anyone have any ideas to what this wrench is used for? And is it a common wrench? Thanks...

Scoutpilot · Post by **Scoutpilot** » Sat Nov 03, 2018 1:59 am

Differential plug wrench.

Mark Jesic · Post by **Mark Jesic** » Sat Nov 03, 2018 2:31 am

Gearbox drain plug ?

Chuck Lutz · Post by **Chuck Lutz** » Sat Nov 03, 2018 6:17 am

Depending on the size, it is for a transfer case and/or the front and rear axles...to remove the drain plugs for some vehicle. Not for a jeep transmission though.

Joe Gopan · Post by **Joe Gopan** » Sat Nov 03, 2018 7:41 am

Chuck, it's in your manuals.
How about 41H-1501 Handle Socket Wrench, Offset, Double End, 1 3/4" x 6 3/4", 1/2" Square Drive.

Check your TM9-803, this is not part of the MB Tool Kit. They are a part of the Motor Vehicle Mechanic's Tool Set.
These can be found availible at an "Ell" of a deal.

RedArrow2016 · Post by **RedArrow2016** » Sat Nov 03, 2018 9:54 am

There were tags on them but they are mostly unreadable at this time but I will measure one today and post the measurements for you that way maybe it will help even more and thanks for all the help so far on this wrench...

Joe Gopan · Post by **Joe Gopan** » Sat Nov 03, 2018 10:38 am

I am familiar with them, have a huge quantity of NOS. What is printed on the side, did you read the respons where I ID''d your pics?

RedArrow2016 · Post by **RedArrow2016** » Sat Nov 03, 2018 10:40 am

So really there is no need for these for anyone then because they are common then I will go to the scrap pile I think with these as well. I do not want to hang on to things that have nobody needing them since they are common out there...

Joe Gopan · Post by **Joe Gopan** » Sat Nov 03, 2018 10:50 am

Don't throw, there are many potential tool collectors that occasionally come out for air.

RedArrow2016 · Post by **RedArrow2016** » Sat Nov 03, 2018 10:58 am

I will get the measurements and your right you never know who or what and when someone will be looking for one...

rjbeamer · Post by **rjbeamer** » Sat Nov 03, 2018 11:27 am

viewtopic.php?t=279979

viewtopic.php?t=272423

Roger

JAB · Post by **JAB** » Sat Nov 03, 2018 1:19 pm

Will a 1/2" drive socket fit on the ends? If so I think I'd like one as a novelty. What brand(s) are they? You might have some other wrenches (I've seen on your other threads) that I might be interested in after I check my "pile" so I'll get back to you in a couple of days. Thanx!

RedArrow2016 · Post by **RedArrow2016** » Sat Nov 03, 2018 1:29 pm

Jeff

I post a better picture here soon tonight with the measurement on it for you as well and thanks....

Gordon_M · Post by **Gordon_M** » Sat Nov 03, 2018 2:06 pm

Ben sent me one of these a while back - thanks again Ben.

Joe Gopan · Post by **Joe Gopan** » Sat Nov 03, 2018 2:26 pm

You're welcome. These are an ugly little critter, and they sort of have a cult like following due to all the different manufacturers names stamped on them, "with cosmoline" or "without cosmoline" also seems to make a difference.

G503 Military Vehicle Message Forums

What is this wrench for any ideas??

What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Re: What is this wrench for any ideas??

Who is online