Drivers Inner Fender Photo needed
- Yinger
- G-Second Lieutenant
- Posts: 520
- Joined: Thu Apr 15, 2004 6:17 am
- Location: Troy, Michigan
Drivers Inner Fender Photo needed
My drivers side fender looks like swiss cheese on the the inside due to misc. holes being added over years of abuse. Does any one have a good picture that shows which holes should be there and which ones do not belong?
Thank you in advance!
Thank you in advance!
John M. Yingling
1943 GPW 139075
1943 Bantam T3 24199
1943 BSA WD M20 96377
MVPA# 27940
1943 GPW 139075
1943 Bantam T3 24199
1943 BSA WD M20 96377
MVPA# 27940
- Hobo
- G-Lieutenant General
- Posts: 4929
- Joined: Sat Aug 09, 2003 8:55 am
- Location: Dithmarschen, "G" - ermany
Sorry, no picture!
But if I counted correctly, there should be max. 26 holes!!! (not counting the two air vents (2) and lamp swivel bracket (1) !!!!!!!)
Top panel:
- two for hold down clamp of hood
- three for BOD light bracket (late only)
- one for BOD wiring clamp (late only)
- one for BOD wiring (late only)
that is 7
Inner forward panel
- three for fender mounting to grill
- one for wiring clip for BO lamps
- two for terminal for wiring for lamps
- one at the bottom for fixing fender to frame
- one for ground strap of braided, shielded wiring going to front
- one for BOD light wiring guided through hat channel
- one for wiring clip
that is 10
hat channel
- two, for fixing to fender
Side panel, rear
- two for fixing to frame, at the very bottom
rear panel
- three for fixing to body
- one, or two (MB / GPW) for fixing to body/step
...were there two or three more for the early MB air deflectors??? Or were these only carried over to the passenger side panels????
But if I counted correctly, there should be max. 26 holes!!! (not counting the two air vents (2) and lamp swivel bracket (1) !!!!!!!)
Top panel:
- two for hold down clamp of hood
- three for BOD light bracket (late only)
- one for BOD wiring clamp (late only)
- one for BOD wiring (late only)
that is 7
Inner forward panel
- three for fender mounting to grill
- one for wiring clip for BO lamps
- two for terminal for wiring for lamps
- one at the bottom for fixing fender to frame
- one for ground strap of braided, shielded wiring going to front
- one for BOD light wiring guided through hat channel
- one for wiring clip
that is 10
hat channel
- two, for fixing to fender
Side panel, rear
- two for fixing to frame, at the very bottom
rear panel
- three for fixing to body
- one, or two (MB / GPW) for fixing to body/step
...were there two or three more for the early MB air deflectors??? Or were these only carried over to the passenger side panels????
Lars-Uwe Rudek
GPW 213313 (HOBO) DoD 7-26-44
GPW 261254 (SUSIE BLUE) DoD 3-26-45 (est.)
MB 177547 (JONSEY) DoD 9-28-42
MB 290875 (HOBBES) DoD 12-21-43
GPW 213313 (HOBO) DoD 7-26-44
GPW 261254 (SUSIE BLUE) DoD 3-26-45 (est.)
MB 177547 (JONSEY) DoD 9-28-42
MB 290875 (HOBBES) DoD 12-21-43
- Jon
- Australian Army (Retired) R.A.E.M.E.
- Posts: 11949
- Joined: Mon May 04, 1998 8:00 pm
- Location: Down Under In Queensland
- Contact:
JeepDraw http://www.g503.com/jeepdraw
Check Hole Locations Section
Left Fender Top (Black Out Light Location & Wiring Holes & Clip) b-o-Loc.gif
Left Inner Fender Panel left-gd.gif
Right Inner Fender Panel le-rt-gd.gif
Lists the locations, sizes of holes, even the tinned areas.
Jon
Check Hole Locations Section
Left Fender Top (Black Out Light Location & Wiring Holes & Clip) b-o-Loc.gif
Left Inner Fender Panel left-gd.gif
Right Inner Fender Panel le-rt-gd.gif
Lists the locations, sizes of holes, even the tinned areas.
Jon
Jon Rogers
AUSTRALIA
http://jeepdraw.com JeepDraw Home Page & Drawings
Parts Colours Page http://jeepdraw.com/PART_COLOURS.htm
1944 GPW195611 20531384 ACM-2 17781
1942 MBT 19433W
AUSTRALIA
http://jeepdraw.com JeepDraw Home Page & Drawings
Parts Colours Page http://jeepdraw.com/PART_COLOURS.htm
1944 GPW195611 20531384 ACM-2 17781
1942 MBT 19433W
- Garret Sawtell
- G-Staff Sergeant
- Posts: 71
- Joined: Mon Mar 17, 2003 4:09 am
- Location: Temperance, MI
- Contact:
- Yinger
- G-Second Lieutenant
- Posts: 520
- Joined: Thu Apr 15, 2004 6:17 am
- Location: Troy, Michigan
- Garret Sawtell
- G-Staff Sergeant
- Posts: 71
- Joined: Mon Mar 17, 2003 4:09 am
- Location: Temperance, MI
- Contact:
-
- G-Lieutenant General
- Posts: 5638
- Joined: Thu Dec 03, 2009 5:29 pm
- Location:
Re: Drivers Inner Fender Photo needed
Hello,
This is great info for locating correct fender holes, when working on fenders with many extra holes .
Ray
This is great info for locating correct fender holes, when working on fenders with many extra holes .
Ray
-
- G-Lieutenant Colonel
- Posts: 1126
- Joined: Mon Oct 19, 2009 8:34 pm
- Location: Texas
Re: Drivers Inner Fender Photo needed
Remember, those are Willys fenders. GPW's have two "fender to step" holes.
Peter
Peter
Who is online
Users browsing this forum: dcrawford, Len Del Calzo, maurywhurt and 95 guests