Chevy and Dodge Factory font registration # stencils

Military Trucks 1/2 ton thru 2 ton, Wanted, For Sale (NO AUCTION or EBAY), and Knowledge Base
Post Reply
Thunderbird712
G-First Lieutenant
G-First Lieutenant
Posts: 689
Joined: Sun Mar 25, 2012 11:19 am
Location: Lexington Park, MD (Southern MD)

Chevy and Dodge Factory font registration # stencils

Post by Thunderbird712 » Thu Jun 23, 2022 5:10 am

I have available the correct factory Chevy G506 font in vinyl paint mask stencil sets. It is available in the early 4" and later 2" size. $35 plus shipping for the hood stencil and another $10 for the third stencil that goes on the tail gate or rear of the truck. Radio suppression S is included if applicable.

Also available is the Dodge WC factory font stencil. I have the 4" 1/2 ton Dodge WC factory font for the models shown in the pictures. I know there were a few 1/2 ton models and am still searching for good pictures of the factory applied registration numbers on all the models to verify the same font was used. Stencil is made using a vinyl paint mask. $35 for the hood set and an extra $10 for the third stencil that goes on the rear of the truck.

Also available is another font used by Dodge. During my research of the factory font for the 3/4 ton and 1 1/2 ton WCs I found a change in font occurred. I am still trying to determine if this change was made when the switch to the 2" font occurred, or when the 3/4 ton WCs were introduced, or was used on certain models. Either way I know this font is correct for the WC-51. If your interested in another 3/4 ton or 1 1/2 ton truck message me and I will work with you to figure out what is correct.

For the motorpool guys, I have a font traced from a WWII stenciling kit. $35 plus shipping for the hood stencil in the vinyl paint mask. This font is frequently seen in period photos. I also do unit markings for the bumper and bumperettes using this font on vehicles and trailers. Full set of unit markings is $30 plus shipping in the vinyl paint mask. I also offer the stencil in a oil board/card stock. Using the oil board/card stock will give you the more authentic look with overspray. Essentially the "messy" look. Discounted price for card stock stencils. Ask for pricing if interested. I will also do a package deal if ordering both the hood stencils and unit markings. At this time, I cannot do the large invasion hood stars.

Lately, I have had issues with getting email notifications informing me I have a PM on the forum. My email address is available in my profile. I prefer email but if you send me a PM here I am not ignoring you if I don't get right back to you. I will make sure to check here often. Also if your interested in a factory font for another vehicle or even other custom stencils I can help. Send me a message and I will work with you to create what you want!

G506
280807709_393442286033277_1745633228439329263_n.jpg
281295851_319646050354732_1171584449321164946_n.jpg
1/2 ton Dodge WC
287111562_3271569633168788_8253070634725821724_n.jpg
285818484_1146376879273647_5896978533867850519_n.jpg
288239852_3407462496204419_4661127299912568437_n.jpg
285557052_734145058022264_2675762544925285783_n.jpg
263554946_296360545594606_8795332312469177934_n.jpg
278703647_654255422281226_1602501734170966040_n.jpg
285589519_1743651089308275_3580827291634133515_n.jpg
TJ Zackman
1945 Willys MB, 430923, 3/28/45
Scored 98.375% at 2019 MVPA Convention York, PA

1953 M38A1, 69248, 12/53, 20999713
MVPA# 37298


Thunderbird712
G-First Lieutenant
G-First Lieutenant
Posts: 689
Joined: Sun Mar 25, 2012 11:19 am
Location: Lexington Park, MD (Southern MD)

Re: Chevy and Dodge Factory font registration # stencils

Post by Thunderbird712 » Thu Jun 23, 2022 5:19 am

Here is the other Dodge font correct for the WC-51 and I believe the other 3/4 ton and large trucks.
287304304_430080598973985_4614923377999696066_n.jpg
287537134_2534579593350615_7537242172745222796_n.jpg
124920489_399857567824410_3348918015947776616_n.jpg
286370814_3206816359645332_4918449857102530452_n.jpg
285503402_1369752536870191_5930933398793507241_n.jpg

Wartime stenciling kit font
285722032_2925661204398450_455183778516188806_n.jpg
285521082_1034865737150826_8520403344101335786_n.jpg
TJ Zackman
1945 Willys MB, 430923, 3/28/45
Scored 98.375% at 2019 MVPA Convention York, PA

1953 M38A1, 69248, 12/53, 20999713
MVPA# 37298

70th Division
G-Lieutenant General
G-Lieutenant General
Posts: 5638
Joined: Thu Dec 03, 2009 5:29 pm
Location:

Re: Chevy and Dodge Factory font registration # stencils

Post by 70th Division » Thu Jun 23, 2022 5:15 pm

Thunderbird712 wrote:
Thu Jun 23, 2022 5:10 am
I have available the correct factory Chevy G506 font in vinyl paint mask stencil sets. It is available in the early 4" and later 2" size. $35 plus shipping for the hood stencil and another $10 for the third stencil that goes on the tail gate or rear of the truck. Radio suppression S is included if applicable.

Also available is the Dodge WC factory font stencil. I have the 4" 1/2 ton Dodge WC factory font for the models shown in the pictures. I know there were a few 1/2 ton models and am still searching for good pictures of the factory applied registration numbers on all the models to verify the same font was used. Stencil is made using a vinyl paint mask. $35 for the hood set and an extra $10 for the third stencil that goes on the rear of the truck.

Also available is another font used by Dodge. During my research of the factory font for the 3/4 ton and 1 1/2 ton WCs I found a change in font occurred. I am still trying to determine if this change was made when the switch to the 2" font occurred, or when the 3/4 ton WCs were introduced, or was used on certain models. Either way I know this font is correct for the WC-51. If your interested in another 3/4 ton or 1 1/2 ton truck message me and I will work with you to figure out what is correct.

For the motorpool guys, I have a font traced from a WWII stenciling kit. $35 plus shipping for the hood stencil in the vinyl paint mask. This font is frequently seen in period photos. I also do unit markings for the bumper and bumperettes using this font on vehicles and trailers. Full set of unit markings is $30 plus shipping in the vinyl paint mask. I also offer the stencil in a oil board/card stock. Using the oil board/card stock will give you the more authentic look with overspray. Essentially the "messy" look. Discounted price for card stock stencils. Ask for pricing if interested. I will also do a package deal if ordering both the hood stencils and unit markings. At this time, I cannot do the large invasion hood stars.

Lately, I have had issues with getting email notifications informing me I have a PM on the forum. My email address is available in my profile. I prefer email but if you send me a PM here I am not ignoring you if I don't get right back to you. I will make sure to check here often. Also if your interested in a factory font for another vehicle or even other custom stencils I can help. Send me a message and I will work with you to create what you want!

G506

280807709_393442286033277_1745633228439329263_n.jpg

281295851_319646050354732_1171584449321164946_n.jpg

1/2 ton Dodge WC

287111562_3271569633168788_8253070634725821724_n.jpg

285818484_1146376879273647_5896978533867850519_n.jpg

288239852_3407462496204419_4661127299912568437_n.jpg

285557052_734145058022264_2675762544925285783_n.jpg

263554946_296360545594606_8795332312469177934_n.jpg

278703647_654255422281226_1602501734170966040_n.jpg

285589519_1743651089308275_3580827291634133515_n.jpg

Hello TJ,


Wow these are awesome !!!

I will get my 1943 3/4 ton Command Car number tomorrow and post it here.
I will order a full set for that Dodge, and will email you to order !
The full USA number is still on the tail gate, so will measure the height.

Keep up your good works !!

Best Regards,
Ray

70th Division
G-Lieutenant General
G-Lieutenant General
Posts: 5638
Joined: Thu Dec 03, 2009 5:29 pm
Location:

Re: Chevy and Dodge Factory font registration # stencils

Post by 70th Division » Fri Jun 24, 2022 11:01 am

Hello,

Here is a picture of the Command Car tailgate USA number :
Resized_received_1079098272486153_(1).jpeg
U.S.A. 20182316


Once the storm is gone I will get a measurement of the number height.

Best Regards,
Ray


Post Reply

Return to “Trucks 1/2 ton thru 2 ton”

Who is online

Users browsing this forum: No registered users and 62 guests