cj2 engine head
-
- G-Captain
- Posts: 762
- Joined: Fri Mar 10, 2006 8:22 am
- Location:
cj2 engine head
folks I have what I think is a cj2 that came with a loose head. the head has the same block number 64--- but has the word JEEP..I found NO serial. but anyone out there that can give me any info about this engine a cast number 5.30 on the head. Not sure what I have but it is a l134 block and all the parts fit as well as the gpw blocks.
-
- G-Lieutenant General
- Posts: 6876
- Joined: Sat Jan 12, 2008 5:25 am
- Location: Tipton,In.
Re: cj2 engine head
Does the head have large, flat ribs on top that run front to rear ??
CJ engine serial number is stamped on top of the engine block. In front of the head, above the water pump.
CJ engine serial number is stamped on top of the engine block. In front of the head, above the water pump.
Mike Wolford
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
-
- G-Lieutenant General
- Posts: 4526
- Joined: Sun Jul 20, 2003 6:03 pm
- Location: Little Meadows PA
Re: cj2 engine head
5-30 is probaly a cast date, probably has willys and jeep on the head, or an aftermarket head as the decimal point is usually a dash 2a heads were both ribbed and non ribbed, what is engine casting number down below dist. or look it up yourself, that list is not complete though.
ADam
http://ww2jeeps.com/htm/heads.htm
ADam
http://ww2jeeps.com/htm/heads.htm
-
- G-Captain
- Posts: 762
- Joined: Fri Mar 10, 2006 8:22 am
- Location:
Re: cj2 engine head
no ribs but I found under the cj forum photos of the different heads. The one I have seems to be for cj2a and cj3 thanks for your answers
-
- G-Lieutenant General
- Posts: 4526
- Joined: Sun Jul 20, 2003 6:03 pm
- Location: Little Meadows PA
Re: cj2 engine head
I do not think any cj3a came from the factory with an unribbed head.
Got a link to that post?
Adam
Got a link to that post?
Adam
-
- G-General
- Posts: 16666
- Joined: Fri Jan 17, 2003 3:40 pm
- Location: Fort Myers, Florida
Re: cj2 engine head
I have a 3a engine 1950 with a ribbed head. I will find the 3a book by Bob W and see if it has info on heads in it.
Stand for the Flag, Kneel for the Cross Psalm 55; 9-11
-
- G-Colonel
- Posts: 1279
- Joined: Mon Sep 04, 2006 4:11 pm
- Location: Ohio
- Contact:
Re: cj2 engine head
PM sent
'45 CJ2A #10033 ACM #47
'45 CJ2A #10163 ACM #188
'45 CJ2A #10749 ACM #951
'45 CJ2A #10910 ACM #1294
'45 CJ2A #10163 ACM #188
'45 CJ2A #10749 ACM #951
'45 CJ2A #10910 ACM #1294
- dpcd67
- G-General
- Posts: 11808
- Joined: Mon Jul 25, 2011 3:41 pm
- Location: Iowa
Re: cj2 engine head
Yes the engines shown in the 3A book al have ribs, as they should; non ribbed heads were not being made then; the M38 used them as did all the Industrial engines. My 51 3A had the ribbed head.
U. S. Army 28 years.
Armor Branch
Armor Branch
Who is online
Users browsing this forum: Bruce W and 47 guests