Page 3 of 3

Mighty Mite Info, CARB REBUILD KIT, (PART NUMBERS)

Posted: Thu Feb 27, 2014 10:15 pm
by mendoza
Can you list and or send me the numbers for the carb. rebuild kit?
Thanks, Pat

pasquale.nj@verizon.net

"I did find a carb rebuild kit that was a exact match and a master cylinder kit that works.I can list #'s if anyone needs them."

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Sat Sep 26, 2015 2:15 pm
by Joe S
I found a part number for the steering box shaft seal.
Timken 480889

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Fri Nov 13, 2015 11:19 am
by Jim Sanders
Could you post the part numbers or email to jim088@hotmail.com thanks

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Sat Dec 19, 2015 10:13 pm
by mspeters
SHOCK ABSORBERS

Transfer post from the dead steel soldiers site

These are Monroe part numbers from 7 years ago. They should still x-ref.
These numbers are similar to the Mite shock specs in the Mite Tech Manuals.

Fronts -- 5753 (10.375" - 16.750") -- Sensa-Trac - mid 50's Mercurys

Rear -- 555003 (9.625" - 14.75") - Gas Magnum RV/trailer shock

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Tue Oct 17, 2017 8:25 pm
by mspeters
Emergency Brake - Rubber Dust Boots

‘39-‘48 Ford - same as original
Available from Mac’s auto parts / Ecklers

Image

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Thu May 03, 2018 6:04 pm
by EvilleMark
Bill, do you you know how to find these spring bushings. I couldn't find on suspension.com
Mark P

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Sun May 13, 2018 6:56 pm
by Radar4xfour
Hello Mark,

Energy Suspension P# is 9.9176G, qty. 16 needed per vehicle.n. Order from any Energy Suspension dealer, mine came from Summit Racing.

Regards,

Radar

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Tue Sep 04, 2018 1:32 pm
by Joe S
here is some updated numbers from some obsolete part numbers. I am posting all that I have again.

Front hub large bearing sets Timken 27690 bearing and 27620 race
Front hub small bearing sets Timken 18790 bearing and 18720 race
Front hub seal National 410708

Rear hub bearing sets National LM67048 bearing and LM67010 race
Or Timken SET6
Rear hub bearing seal National 473445 or SKF 16680

Engine front pulley seal National 473367

Steering box shaft seal Timken 480889

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Mon Oct 01, 2018 4:51 pm
by jrlatt
Hello

My name is Roger. I just became a member. looking forward to exchanging information. I was wondering if anyone has the carb rebuild kit numbers.

Thanks

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Sat Oct 13, 2018 1:35 pm
by first 422
Hi Roger,
I found this carb kit from carbs unlimited #KT-5105 but it does not have the correct bowl gasket. It does have the correct accel pump, power valve and float needle and seat and the throttle plate to body gasket. I saw the bowl gasket on M422a1.com website.

I hope that this helps!

Ed H

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Sun Oct 28, 2018 9:14 pm
by jrlatt
Hello Ed

Thanks for the information.

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Fri Nov 30, 2018 7:26 pm
by mspeters
Pinion Seals for front and Rear diff.

Standard = 5778 Timken - Nitrile rubber

Modern crossover = 4941V Timken; SKF 15791 - These are both Fluoroelastomer

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Wed Mar 06, 2019 1:14 pm
by mendoza
lawverdict wrote:
Sun Mar 31, 2013 5:35 pm
A carb rebuild kit number and brake master cylinder rebuild number would be appreciated.
DID anyone come up with the Answer?

Re: Some Handy Mighty Mite Info (PART NUMBERS)

Posted: Sat Mar 30, 2019 8:00 am
by Babadave
Carb kits 'per se' ? No, nothing is a direct and complete kit for this Holley.
You can get various kits that come close. But nothing I have found is a direct exact complete rebuild kit.
I have had good success with this place :

https://daytonaparts.com/

They clean, replate as necessary and rebuild. They will even test run on a donkey engine and do initial settings. Not 'too' bad $ wise considering ? I have had 6 re-done there with Eathanol resistant rubber. They are all still going strong.

Brake master cylinder kit, same as above. This is a old Lockheed design. Aluminum bore. Fiddily to rebuild.
You can still find NOS Master cylinders on EBay, and most of the vendors. There ARE rebuild kits on EPay as well. NOS original kits are the way to go IMHO if your bore hones and cleans up perfectly

Good luck !

Pushrod tube springs

Posted: Mon Jun 24, 2019 10:10 pm
by mspeters
These pushrod tube springs can replace the rusty mite springs.

Image

Centuryspring.com
# 71957-5