Page 3 of 4
Mighty Mite Info, CARB REBUILD KIT, (PART NUMBERS)
Posted: Thu Feb 27, 2014 8:15 pm
by mendoza
Can you list and or send me the numbers for the carb. rebuild kit?
Thanks, Pat
"I did find a carb rebuild kit that was a exact match and a master cylinder kit that works.I can list #'s if anyone needs them."
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Sat Sep 26, 2015 1:15 pm
by Joe S
I found a part number for the steering box shaft seal.
Timken 480889
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Fri Nov 13, 2015 9:19 am
by Jim Sanders
Could you post the part numbers or email them. thanks
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Sat Dec 19, 2015 8:13 pm
by mspeters
SHOCK ABSORBERS
Transfer post from the dead steel soldiers site
These are Monroe part numbers from 7 years ago. They should still x-ref.
These numbers are similar to the Mite shock specs in the Mite Tech Manuals.
Fronts -- 5753 (10.375" - 16.750") -- Sensa-Trac - mid 50's Mercurys
Rear -- 555003 (9.625" - 14.75") - Gas Magnum RV/trailer shock
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Tue Oct 17, 2017 7:25 pm
by mspeters
Emergency Brake - Rubber Dust Boots
‘39-‘48 Ford - same as original
Available from Mac’s auto parts / Ecklers
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Thu May 03, 2018 5:04 pm
by EvilleMark
Bill, do you you know how to find these spring bushings. I couldn't find on suspension.com
Mark P
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Sun May 13, 2018 5:56 pm
by Radar4xfour
Hello Mark,
Energy Suspension P# is 9.9176G, qty. 16 needed per vehicle.n. Order from any Energy Suspension dealer, mine came from Summit Racing.
Regards,
Radar
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Tue Sep 04, 2018 12:32 pm
by Joe S
here is some updated numbers from some obsolete part numbers. I am posting all that I have again.
Front hub large bearing sets Timken 27690 bearing and 27620 race
Front hub small bearing sets Timken 18790 bearing and 18720 race
Front hub seal National 410708
Rear hub bearing sets National LM67048 bearing and LM67010 race
Or Timken SET6
Rear hub bearing seal National 473445 or SKF 16680
Engine front pulley seal National 473367
Steering box shaft seal Timken 480889
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Mon Oct 01, 2018 3:51 pm
by jrlatt
Hello
My name is Roger. I just became a member. looking forward to exchanging information. I was wondering if anyone has the carb rebuild kit numbers.
Thanks
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Sat Oct 13, 2018 12:35 pm
by first 422
Hi Roger,
I found this carb kit from carbs unlimited #KT-5105 but it does not have the correct bowl gasket. It does have the correct accel pump, power valve and float needle and seat and the throttle plate to body gasket. I saw the bowl gasket on M422a1.com website.
I hope that this helps!
Ed H
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Sun Oct 28, 2018 8:14 pm
by jrlatt
Hello Ed
Thanks for the information.
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Fri Nov 30, 2018 5:26 pm
by mspeters
Pinion Seals for front and Rear diff.
Standard = 5778 Timken - Nitrile rubber
Modern crossover = 4941V Timken; SKF 15791 - These are both Fluoroelastomer
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Wed Mar 06, 2019 11:14 am
by mendoza
lawverdict wrote: ↑Sun Mar 31, 2013 4:35 pm
A carb rebuild kit number and brake master cylinder rebuild number would be appreciated.
DID anyone come up with the Answer?
Re: Some Handy Mighty Mite Info (PART NUMBERS)
Posted: Sat Mar 30, 2019 7:00 am
by Babadave
Carb kits 'per se' ? No, nothing is a direct and complete kit for this Holley.
You can get various kits that come close. But nothing I have found is a direct exact complete rebuild kit.
I have had good success with this place :
https://daytonaparts.com/
They clean, replate as necessary and rebuild. They will even test run on a donkey engine and do initial settings. Not 'too' bad $ wise considering ? I have had 6 re-done there with Eathanol resistant rubber. They are all still going strong.
Brake master cylinder kit, same as above. This is a old Lockheed design. Aluminum bore. Fiddily to rebuild.
You can still find NOS Master cylinders on EBay, and most of the vendors. There ARE rebuild kits on EPay as well. NOS original kits are the way to go IMHO if your bore hones and cleans up
perfectly
Good luck !
Pushrod tube springs
Posted: Mon Jun 24, 2019 9:10 pm
by mspeters
These pushrod tube springs can replace the rusty mite springs.
Centuryspring.com
# 71957-5