Parting a PU58 Prices Edited

Knowledge Base NO EBAY or COMMERCIAL SALES.
Post Reply
wadefreedomvehicles
G-First Sergeant
G-First Sergeant
Posts: 138
Joined: Fri Apr 10, 2015 9:53 pm
Location: Orem Utah
Contact:

Parting a PU58 Prices Edited

Post by wadefreedomvehicles » Fri Aug 10, 2018 12:04 pm

I am keeping some parts for myself.
But most of it is for sale.
Side covers I am keeping, oil filter canister, generator(on engine), Panel cover, Pully off governor.

Engine with no oil filter or generator. Engine in unkown condition. Probably needs rebuilt. I believe it is a DJ3 Engine. (has recently redone starter) $200
Generator $100
Radiator $100
Panel(gauges, etc) $100
Fuel tank $50
Air filter $75

The generator was built into a trailer and air compressor unit. Whatever is left after part out Will be scrapped.
All parts are OBO. If a part is not listed you can ask about it.
Link to photos:
https://photos.app.goo.gl/TxH5MELFNjPSb6LF7
Last edited by wadefreedomvehicles on Wed Aug 29, 2018 11:55 am, edited 2 times in total.

Adam
G-Lieutenant Colonel
G-Lieutenant Colonel
Posts: 1116
Joined: Sun Jul 20, 2003 7:03 pm
Location: Little Meadows PA

Re: Parting a PE95 Prices Edited

Post by Adam » Sat Aug 18, 2018 10:35 pm

Looks like a PU58 not a PE95, Whats the VR under the cover look like?

Do you have a side view picture of the intake?

Adam

wadefreedomvehicles
G-First Sergeant
G-First Sergeant
Posts: 138
Joined: Fri Apr 10, 2015 9:53 pm
Location: Orem Utah
Contact:

Re: Parting a PE95 Prices Edited

Post by wadefreedomvehicles » Wed Aug 22, 2018 7:45 pm

Voltage regulator, Where is that found?

wadefreedomvehicles
G-First Sergeant
G-First Sergeant
Posts: 138
Joined: Fri Apr 10, 2015 9:53 pm
Location: Orem Utah
Contact:

Re: Parting a PU58 Prices Edited

Post by wadefreedomvehicles » Wed Aug 29, 2018 11:56 am

Really would like to see these parts go somewhere rather than scrap.

Adam
G-Lieutenant Colonel
G-Lieutenant Colonel
Posts: 1116
Joined: Sun Jul 20, 2003 7:03 pm
Location: Little Meadows PA

Re: Parting a PU58 Prices Edited

Post by Adam » Wed Aug 29, 2018 8:38 pm

Look under that long cover on top of the generator right behind the engine held in by probably for flat head screws you say there was a generator mounted on the engine then without voltage regulator is under that cover
Last edited by Adam on Thu Aug 30, 2018 2:46 pm, edited 1 time in total.


wadefreedomvehicles
G-First Sergeant
G-First Sergeant
Posts: 138
Joined: Fri Apr 10, 2015 9:53 pm
Location: Orem Utah
Contact:

Re: Parting a PU58 Prices Edited

Post by wadefreedomvehicles » Thu Aug 30, 2018 8:26 am

Okay thanks.
And your thing about the generator makes no sense...

blitz67
G-First Lieutenant
G-First Lieutenant
Posts: 655
Joined: Sun Mar 19, 2006 12:54 pm
Location: Citrus Heights, Ca.

Re: Parting a PU58 Prices Edited

Post by blitz67 » Thu Sep 06, 2018 9:56 am

I usually scrap out most of what is left too, there is just no demand for the parts, I have offered several parts on here over the years for free and as of yet, not one taker, not one. So scrap away

blitz67
G-First Lieutenant
G-First Lieutenant
Posts: 655
Joined: Sun Mar 19, 2006 12:54 pm
Location: Citrus Heights, Ca.

Re: Parting a PU58 Prices Edited

Post by blitz67 » Thu Sep 06, 2018 9:57 am

But don't forget the voltage regulator, I had a PU-58 a couple months ago and almost missed it. Mine was like new.

Tim Shanteler
G-First Sergeant
G-First Sergeant
Posts: 132
Joined: Sat Sep 06, 2008 6:20 pm

Re: Parting a PU58 Prices Edited

Post by Tim Shanteler » Fri Sep 07, 2018 6:42 am

Are the small tabs (spring loaded) that are used to keep the panels in place available? I need a few.

Regards,

Tim
Tim

1945 WC-57 81674456
1944 WC-52 81750129
1945 MB 430629
1943 Ford GPW133609
1943 Ben Hur 0347395 (Gertstenlager)

wadefreedomvehicles
G-First Sergeant
G-First Sergeant
Posts: 138
Joined: Fri Apr 10, 2015 9:53 pm
Location: Orem Utah
Contact:

Re: Parting a PU58 Prices Edited

Post by wadefreedomvehicles » Tue Sep 11, 2018 10:36 am

Tim yes they are. I can pull them off.

Tim Shanteler
G-First Sergeant
G-First Sergeant
Posts: 132
Joined: Sat Sep 06, 2008 6:20 pm

Re: Parting a PU58 Prices Edited

Post by Tim Shanteler » Tue Sep 11, 2018 10:41 am

Great! PM me what you want for them and how to pay.

Tim
Tim

1945 WC-57 81674456
1944 WC-52 81750129
1945 MB 430629
1943 Ford GPW133609
1943 Ben Hur 0347395 (Gertstenlager)

Post Reply

Return to “Willys Go Devil Engine Based GENERATOR SETS and COMPRESSORS(Includes Hobart Bros. & other GenSets)”

Who is online

Users browsing this forum: No registered users and 6 guests