M151A1 begining of new project
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
M151A1 begining of new project
I'm not a MUTT guru for starters, I'm HMMWV guru so if I ask a dumb question don't laugh My only experience with 151 was when I was stationed in Korea (87)for a year and I only changed out a few clutch's and engines because these vehicles never broke
Just bought a M151A1, Ford ORD built in 1966 and is a no runner. So I have two issues:
1. The head has a stuck valve but the engine turns free. Before I begin to put batteries in it to check what should I check as far as fuel? The seller stated "is a friend not some random person" its been parked in the garage for 15 years and was running on regular fuel. Then began to run unleaded fuel that's when it began to have the valve sticking. Can these engines be run with unleaded fuel?
2. The brake pedal drops to the floor, I think either its has no brake fluid or a bad master cylinder. Is the square plug on the windshield frame the reservoir for the master cylinder? Does this take Dot5?
Today is day one of research so I'm going to be looking up some TM's or Pubs to locate items and parts I will need. It also appears I'm missing the correct fender lights and would like a picture of the correct lights for the 66 Ford if anybody has? Thanks in advance for your input and any help is greatly appreciated.
Robert
Just bought a M151A1, Ford ORD built in 1966 and is a no runner. So I have two issues:
1. The head has a stuck valve but the engine turns free. Before I begin to put batteries in it to check what should I check as far as fuel? The seller stated "is a friend not some random person" its been parked in the garage for 15 years and was running on regular fuel. Then began to run unleaded fuel that's when it began to have the valve sticking. Can these engines be run with unleaded fuel?
2. The brake pedal drops to the floor, I think either its has no brake fluid or a bad master cylinder. Is the square plug on the windshield frame the reservoir for the master cylinder? Does this take Dot5?
Today is day one of research so I'm going to be looking up some TM's or Pubs to locate items and parts I will need. It also appears I'm missing the correct fender lights and would like a picture of the correct lights for the 66 Ford if anybody has? Thanks in advance for your input and any help is greatly appreciated.
Robert
Last edited by Hell On Wheels on Fri Aug 23, 2019 4:26 pm, edited 3 times in total.
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
- muttguru
- G-Colonel
- Posts: 1698
- Joined: Fri Jul 18, 2003 11:46 am
- Location: Lil' ol' England
- Contact:
Re: M151A1 possible fuel issue and master cylinder
Hello Robert,
I've just seen your posts on the board. If you email me directly at muttguru@aol.com it will make it much easier to provide you with information, pictures etc.
Kind regards....
Ken
I've just seen your posts on the board. If you email me directly at muttguru@aol.com it will make it much easier to provide you with information, pictures etc.
Kind regards....
Ken
Contact address - muttguru@aol.com
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
Re: M151A1 possible fuel issue and master cylinder
Will do, email forthcoming.
Thank you
Thank you
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
-
- G-Lieutenant General
- Posts: 5918
- Joined: Sun Mar 19, 2006 10:04 am
- Location: Pemberton, New Jersey
Re: M151A1 possible fuel issue and master cylinder
Since you are already in capable hands I will just say welcome and wait for any further questions.
Rick
Rick
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
Re: M151A1 begining of new project
I changed the original post name as I will use this as my information board. Just a few questions and an update photo of work in progress. Just removed all items not military and installed the original bumper its all bent up when I get to the final stage to paint I will replace it. I wanted to give a shout out to Muttguru who has provided me with some important information and Leo from Texas who I have just began buying parts from and getting knowledge from both and members on the board many thanks.
Status Update: batteries, battery tray, battery hardware, master and wheel cylinders will be here on Monday. Still need some B/O for the front grill, seat cushions and relocate the turn signals from the grill to the fenders. That's another day as the harness was badly modified and I need to locate the original wire supply.
Q1. I have a rust question, what is best solvent to use to stop the surface rust? Will CLR work?
Q2. I was working on my rocker arm assembly, I couldn't find the torq specs on the rocker arm. I found the head (65-70 lb-ft) and valve cover (10-15 lb-ft) torq specs, can anybody help?
Thanks
Robert
Status Update: batteries, battery tray, battery hardware, master and wheel cylinders will be here on Monday. Still need some B/O for the front grill, seat cushions and relocate the turn signals from the grill to the fenders. That's another day as the harness was badly modified and I need to locate the original wire supply.
Q1. I have a rust question, what is best solvent to use to stop the surface rust? Will CLR work?
Q2. I was working on my rocker arm assembly, I couldn't find the torq specs on the rocker arm. I found the head (65-70 lb-ft) and valve cover (10-15 lb-ft) torq specs, can anybody help?
Thanks
Robert
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
-
- G-Lieutenant General
- Posts: 5918
- Joined: Sun Mar 19, 2006 10:04 am
- Location: Pemberton, New Jersey
Re: M151A1 begining of new project
I think I answered this somewhere, maybe a different forum? 35-40 ft.lbs.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
- muttguru
- G-Colonel
- Posts: 1698
- Joined: Fri Jul 18, 2003 11:46 am
- Location: Lil' ol' England
- Contact:
Re: M151A1 begining of new project
You did indeed, Rick..... here it is........Rickf wrote:I think I answered this somewhere, maybe a different forum? 35-40 ft.lbs.
viewtopic.php?f=14&t=98221
Hello Robert.....it looks better already !
Ken
Contact address - muttguru@aol.com
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
Re: M151A1 begining of new project
Thanks Ken & Rick,
Should be finally a cool day here in San Antonio so Ill work on it for a short bit until the rest of parts come it. No Drag Racing (The Sarge) to watch today and Football (Cowboys) comes on a few hours.
Should be finally a cool day here in San Antonio so Ill work on it for a short bit until the rest of parts come it. No Drag Racing (The Sarge) to watch today and Football (Cowboys) comes on a few hours.
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
Re: M151A1 begining of new project
Bad news today when cleaning out my tank. Its full of crap and rusted as hell. Looking over it I think its best to replace it. Are theses hard to find? What is the difference from a A1 vs. A2 tank?
Last edited by Hell On Wheels on Fri Aug 23, 2019 4:25 pm, edited 1 time in total.
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
-
- G-Major
- Posts: 832
- Joined: Sun Dec 20, 2009 9:35 pm
- Location:
Re: M151A1 begining of new project
I got my a2 gas tank from red river parts check with blake they should be able to help you
903 5472226
frenchman
903 5472226
frenchman
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
Re: M151A1 begining of new project
Update on my project.
Just replaced master cylinder and all wheel cylinders. Tested all lines and blew them out and cleaned them. Brakes are good to go. Replaced all battery post. I found a NOS A1 tank and should have it by Friday along with a slew of small parts to include new fuel lines, filter, carburetor, valve cover, seat cushions, battery tray, turn signal covers, B/O stop light, some rattle cans and front bumper etc.... to spot paint as I go along. Altogether I convinced myself to think it only cost me only $500.00, then I felt better .
I do have a question what is the part number of the rubber seal/gasket that is on the bottom of the windshield between the frame and cow panel? I couldn’t find it in the TM. I see it as a dotted item but not identified to a part number.
Robert
Just replaced master cylinder and all wheel cylinders. Tested all lines and blew them out and cleaned them. Brakes are good to go. Replaced all battery post. I found a NOS A1 tank and should have it by Friday along with a slew of small parts to include new fuel lines, filter, carburetor, valve cover, seat cushions, battery tray, turn signal covers, B/O stop light, some rattle cans and front bumper etc.... to spot paint as I go along. Altogether I convinced myself to think it only cost me only $500.00, then I felt better .
I do have a question what is the part number of the rubber seal/gasket that is on the bottom of the windshield between the frame and cow panel? I couldn’t find it in the TM. I see it as a dotted item but not identified to a part number.
Robert
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
- muttguru
- G-Colonel
- Posts: 1698
- Joined: Fri Jul 18, 2003 11:46 am
- Location: Lil' ol' England
- Contact:
Re: M151A1 begining of new project
Robert, it is listed officially as "Seal, Non-Metallic" but it is generally referred to as the "rubber windshield-to-body seal" (or gasket).Hell On Wheels wrote:I do have a question what is the part number of the rubber seal/gasket that is on the bottom of the windshield between the frame and cow panel?
Robert
Part Number is 11660447. NSN is 5330-00-151-4360
Before you install it, go to the G838 board and read up about installing the seal. You'll find several references to this task. It may save you some heartache if you see how other owners installed theirs.
Ken
Contact address - muttguru@aol.com
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
-
- Sergeant Major of the Gee
- Posts: 419
- Joined: Wed Oct 23, 2013 6:25 am
- Location: El Dorado, Ar.
Re: M151A1 begining of new project
Where did you find NOS A1 tank?
- Hell On Wheels
- G-Colonel
- Posts: 1530
- Joined: Fri May 04, 2007 1:19 pm
- Location: San Antonio, TX
- Contact:
Re: M151A1 begining of new project
Ken,
Thanks for the info.
Hambone,
I was able to buy from Frontline 717-252-4489, keep in mind it wasnt cheap but NOS. Here is a link with lots of suppliers I used for research if you dont have already.
http://www.imfmotorpool.com/partsdealers.html
Thanks for the info.
Hambone,
I was able to buy from Frontline 717-252-4489, keep in mind it wasnt cheap but NOS. Here is a link with lots of suppliers I used for research if you dont have already.
http://www.imfmotorpool.com/partsdealers.html
Robert
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
1966 - M151A1
1986 - M998
2007 - M1102
2009 - H3T
Hell on Wheels https://www.youtube.com/channel/UCi_blL ... z7Ukw8gbHg
-
- G-Lieutenant General
- Posts: 5918
- Joined: Sun Mar 19, 2006 10:04 am
- Location: Pemberton, New Jersey
Re: M151A1 begining of new project
Just a hint, those rattle cans you bought from him in Pa. came from your neighbor in Texas. He buys his paint from Rapco most likely as do most of the vendors.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Who is online
Users browsing this forum: No registered users and 15 guests