steering column or seat modifications

1941 - 1945, MB, GPW modifications, sugestions, and ideas, official MWO's and unofficial WWII field mods NO EBAY or COMMERCIAL SALES.
Chuck Lutz
Gee Addict
Posts: 24778
Joined: Wed Jun 28, 2006 8:00 am
Location: Novato, CA

Re: steering column or seat modifications

Post by Chuck Lutz » Tue Apr 10, 2018 10:58 am

1) remove column from jeep
2) carefully cut a section out of the tube
3) carefully cut a section out of the shaft
4) install new upper bearing in shaft
5) weld splined end of shaft to original shaft

Voila! kinda like Tom's suggestion...
Chuck Lutz

GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
GPW 108552 4/17/43 Louisville, KY. USA 20371278 (DOD est./Tom W.)
Bantam T3 4582 10/29/42 USA 0173499 (est.)

semberae
G-Sergeant First Class
G-Sergeant First Class
Posts: 92
Joined: Mon Jul 11, 2016 5:20 pm
Location: south central Texas

Re: steering column or seat modifications

Post by semberae » Tue Apr 10, 2018 4:26 pm

Is that safe to cut and weld the steering shaft??? :?:

Marty, SoCal
G-Lieutenant General
G-Lieutenant General
Posts: 5969
Joined: Thu Mar 09, 2006 12:34 pm

Re: steering column or seat modifications

Post by Marty, SoCal » Wed Apr 11, 2018 8:30 am

If it's done by a certified welder it will be!
43 Ford GPW 92098
53 Dunbar Kapple M100
Sold: 61 CJ-5, 41 T207 WC-1 Dodge closed cab pickup
MVPA #8266
USMC Tanker (1811, 1812), 85-93
ASE Automotive Master tech, former Chrysler-Jeep Level 4 Mastertech, CA state EA smog license

AJT-AZ
G-Private
G-Private
Posts: 6
Joined: Thu May 10, 2018 4:57 pm
Location: Tonopah, AZ

Re: steering column or seat modifications

Post by AJT-AZ » Thu Oct 11, 2018 7:42 am

I was a welder and I think that would be a clean way to shorten the shaft. Tig welding would be the best way.

DUNK
G-Sergeant
G-Sergeant
Posts: 31
Joined: Fri Jul 09, 2010 2:52 pm
Location: reno,nevada

Re: steering column or seat modifications

Post by DUNK » Mon Nov 12, 2018 3:01 pm

phendriks82 wrote:
Thu Jan 18, 2018 12:39 pm
Hello im in the process of trying to restore my ww2 willys jeep,
however im not the skinniest person and the steering wheel is very uncomfortably close to my gut ,
how can we modify this without messing with the originality too much?

1:can the steering column be shortened, and if so how? or would this result in the opposite: my knees hitting the steering wheel?
2: is there a way to modify the seat other than thinner cussions? without cutting stuff up too much (cutting in the seat is fine)

at the moment it is very uncomfortable to drive, even so for a less "big" friend of mine.
so any help would be appreciated.
I cannot see why a smaller,say 14 inch wheel could be made as there is a great deal of interest in this subject. The KISS principal applies here for sure.
I have looked at dozens of stg. wheels over the years and have yet to find a proper fit that is not 17 inches.


User avatar
W. Winget
LTC, U.S. Army
LTC, U.S. Army
Posts: 2197
Joined: Mon Dec 16, 2002 12:37 pm
Location: USA, Virginia, Carrollton
Contact:

Re: steering column or seat modifications

Post by W. Winget » Tue Nov 13, 2018 6:47 am

phendriks82 wrote:
Mon Mar 26, 2018 12:19 pm
does anyone know if a steering column of perhaps a later model (CJ series) which is shorter might fit?
My '42 appears to have a M38? Column, (the horn wire goes through the end of the steering box)
When compared to my friends 44 Willy, it's about 1" more clearance right where it counts with the wheel about 1" closer to the dash.
V/R W WInget
Looking for 1918 Standard B 'Liberty' truck parts

Adam
G-Lieutenant Colonel
G-Lieutenant Colonel
Posts: 1193
Joined: Sun Jul 20, 2003 7:03 pm
Location: Little Meadows PA

Re: steering column or seat modifications

Post by Adam » Sun Nov 18, 2018 3:45 pm

I use a smaller wheel from a tractor, direct fit, chances of finding one though are slim, It works fine, it is black rubber type material. steers fine. You can always get a cj wheel, get the plastic off it, cut the spokes off at the outside and weld them to a smaller tractor steering wheel, then get it recovered. lots of work. Jeep police will moan. Put the original wheel back on when I did the seat move back.

I also did the seat move back cut the wheel well mumbo jumbo. My own fab, did not buy the ready to go kit. It has its issues too, welding, cutting,painting, When getting out the hip cushion is in the way so you have to wiggle and twist to get out, seat cushion don't feel right. Has to do with its not back far enough. More knee room under the steer column and a little easier to push the pedals. I am happy with this method, Makes driving the jeep fun again.

Adam

Post Reply

Return to “MB GPW Modifications”

Who is online

Users browsing this forum: No registered users and 5 guests