Differential Carrier Bearing Question
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Differential Carrier Bearing Question
I opened up my rear differential today. (yeah, I posted like a year ago it was done. Then I started building the front diff and decided to go back and re-look a layer or two deeper.)
Anyway, I came upon an interesting problem.
One of the carrier bearing races (cup) is really chewed up, but the other one is perfect. Is it acceptable to only change the bad race and leave all other shims and settings intact, or should I change both of them regardless?
Thanks. I'm sure more questions will surface out of this as I have not completed cleaning all the bearings and gears. The race that is ruined looks like it got chewed up by a stray fragment of metal.
Anyway, I came upon an interesting problem.
One of the carrier bearing races (cup) is really chewed up, but the other one is perfect. Is it acceptable to only change the bad race and leave all other shims and settings intact, or should I change both of them regardless?
Thanks. I'm sure more questions will surface out of this as I have not completed cleaning all the bearings and gears. The race that is ruined looks like it got chewed up by a stray fragment of metal.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- G-Command Sergeant Major
- Posts: 236
- Joined: Wed Jul 15, 2009 3:27 pm
- Location:
Re: Differential Carrier Bearing Question
The bearings should be replaced in sets.
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: Differential Carrier Bearing Question
Same with the races, right? I'm not replacing the bearings if I don't have too, but preliminary inspection, I think I have a bad one.hatchetdan wrote:The bearings should be replaced in sets.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
- JAB
- G-General
- Posts: 9586
- Joined: Fri Dec 13, 2002 5:25 pm
- Location: under the jeep in North Prairie, WI
Re: Differential Carrier Bearing Question
lt.luke wrote:Same with the races, right? I'm not replacing the bearings if I don't have too, but preliminary inspection, I think I have a bad one.hatchetdan wrote:The bearings should be replaced in sets.
You can see the damage in the cup, right? What makes you think the cone is any better just because you can't see it under the rollers & cage?
-Jeff
GR8GPN2U!!!
GR8GPN2U!!!
-
- G-Colonel
- Posts: 1345
- Joined: Sun Sep 09, 2007 9:45 am
- Location: Northern California
Re: Differential Carrier Bearing Question
Luke,
Tapered roller bearings should be replaced as a set; cup and cone. Finish the teardown of the carrier from the differencial housing retaining shim packs and bearings marked for which side they came from. Inspect the cups and cones for wear and damage and if any one piece of that bearing shows damage that set should be replaced as a cup and cone. The preload of the bearings will need to be set to this new bearing(s) as described in the manual.
What you don't want to do is get everything done and the first test drive shows a real noisey bearing in the differencial. Do it once, it may cost a little more now but will save you more in money and time in the long run. Just my opinion.
Regards
Bill
Tapered roller bearings should be replaced as a set; cup and cone. Finish the teardown of the carrier from the differencial housing retaining shim packs and bearings marked for which side they came from. Inspect the cups and cones for wear and damage and if any one piece of that bearing shows damage that set should be replaced as a cup and cone. The preload of the bearings will need to be set to this new bearing(s) as described in the manual.
What you don't want to do is get everything done and the first test drive shows a real noisey bearing in the differencial. Do it once, it may cost a little more now but will save you more in money and time in the long run. Just my opinion.
Regards
Bill
Bill
I've never met anyone I couldn't like, until proven wrong.
USN ADJ2 67-71
GPW 178896 probable 1-27-44 to 2-14-44 DOD ??
frame off completed 4/15 USN
MVPA #22119 MVCC 12480
I've never met anyone I couldn't like, until proven wrong.
USN ADJ2 67-71
GPW 178896 probable 1-27-44 to 2-14-44 DOD ??
frame off completed 4/15 USN
MVPA #22119 MVCC 12480
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Differential Carrier Bearing Question
The Bearings and Cups are ground to a very close tolerance. You did not indicate if it was the inner or outer. The inner Bearing is the one that is pressed all the way onto the shaft, it will have to go to a machine shop to be removed and replaced. pressing it on is very touchy as it can get cocked and will jam if not replaced on a press that applies even pressure. The Cup for the inner may be installed using the same shim settings, as the tolerances the bearings and cups are made to a very tight tolerance that is not enough to alter the depth of the inner cup. The outer bearing is the one where the preload is determined by adding or subtracting shims. It is best to order a pinion gear shim pack from your Jeep parts supplier. Adjust the preload before you install the pinion seal, then install the seal once it is adjusted. Pay attention to where the slinger on the pinion shaft is located, follow your manual.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: Differential Carrier Bearing Question
Carrier bearings Ben, not pinion bearings. Can the bearings be replaced without changing shims?Ben Dover wrote:The Bearings and Cups are ground to a very close tolerance. You did not indicate if it was the inner or outer. The inner Bearing is the one that is pressed all the way onto the shaft, it will have to go to a machine shop to be removed and replaced. pressing it on is very touchy as it can get cocked and will jam if not replaced on a press that applies even pressure. The Cup for the inner may be installed using the same shim settings, as the tolerances the bearings and cups are made to a very tight tolerance that is not enough to alter the depth of the inner cup. The outer bearing is the one where the preload is determined by adding or subtracting shims. It is best to order a pinion gear shim pack from your Jeep parts supplier. Adjust the preload before you install the pinion seal, then install the seal once it is adjusted. Pay attention to where the slinger on the pinion shaft is located, follow your manual.
I don't intend to remove the pinion.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
- artificer
- banned
- Posts: 13558
- Joined: Tue Jul 11, 2006 10:46 am
- Location: SINGAPORE
Re: Differential Carrier Bearing Question
I thought this thread was about the differential carrier bearings, not pinion bearings?
If so you can get external shims to move the bearing cups [adjust the crown wheel positioning & bearing pre-load]rather than internal, under the bearing cone type, which makes adjustments a breeze.
Rear Axle Differential Bearing Shim Kit
Ford GPW 18388
Willys A 6744
If so you can get external shims to move the bearing cups [adjust the crown wheel positioning & bearing pre-load]rather than internal, under the bearing cone type, which makes adjustments a breeze.
Rear Axle Differential Bearing Shim Kit
Ford GPW 18388
Willys A 6744
John GIBBINS Member Institute of Automotive Mechanical Engineers [Ret], ASE Master Medium/Heavy Truck & Auto Technician USA -2002 Licensed Motor Mech NSW MVIC 49593 Current 2015
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Differential Carrier Bearing Question
Sorry bout that, save it for the pinion gear in case you may need it. As for the Carrier Bearings, just replace the cups and bearings, do not disturb or mix the shims as the pack is likely thicker on one side. They are ground to the same tolerance and if the stars are shining in your favor, they will retain the preload and backlash adjustment. You will note a relief on either side of the case, if you are careful, you will be able to remove each bearing with a long tapered punch, and replace the same way. Just be cautious and do not let the tapered punch contact the bearing cage when driving them. If I were closer I would do it for you with the Jeep Tool Set I have. The job is not as hard as it appears.If the differential goes in without having to force it, the preload is likely insufficient and you will have to remove both bearings and shims and start the procedure as shown in your manual.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: Differential Carrier Bearing Question
According to this, the bearings would go all the way on (bottom out on the carrier) and the shims you mention would go between th race & the housing?artificer wrote:I thought this thread was about the differential carrier bearings, not pinion bearings?
If so you can get external shims to move the bearing cups [adjust the crown wheel positioning & bearing pre-load]rather than internal, under the bearing cone type, which makes adjustments a breeze.
Rear Axle Differential Bearing Shim Kit
Ford GPW 18388
Willys A 6744
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Differential Carrier Bearing Question
No, the shims are placed on the Differential Case before the Tapered Bearings are installed.
A check of your SNL will confirm.
A check of your SNL will confirm.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: Differential Carrier Bearing Question
Thanks Ben. You said:
I've checked the bearings. There are no bad spots on the rollers, but they both gritty, & will be replaced.
I do not have to "force in" the carrier now, just rotate the pinion gear & it goes in fairly easily. What's your definition of "force in"?If the differential goes in without having to force it, the preload is likely insufficient and you will have to remove both bearings and shims and start the procedure as shown in your manual.
I've checked the bearings. There are no bad spots on the rollers, but they both gritty, & will be replaced.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Differential Carrier Bearing Question
The procedure for determining preload is install the bearings without shims and put the unit into the differential housing, force it to one side and measure the space outside the bearing cup (race) and the side of the axle housing with a feeler gauge, this will determine the zero clearance and a corresponding amount of shils are aded. To that 0.008" more shims are added to the previous total to give the bearings necessary preload. This is all in the TM you should have at your side.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- artificer
- banned
- Posts: 13558
- Joined: Tue Jul 11, 2006 10:46 am
- Location: SINGAPORE
Re: Differential Carrier Bearing Question
That is what I said. Joel is not the only person who ever did this task.you can get external shims to move the bearing cups [adjust the crown wheel positioning & bearing pre-load]rather than internal, under the bearing cone type, which makes adjustments a breeze
There are always easier shortcuts & this is one people who work on differentals for a living will use over & above what TM closetted specialists spruik. Thinking outside the box is a good thing.
John GIBBINS Member Institute of Automotive Mechanical Engineers [Ret], ASE Master Medium/Heavy Truck & Auto Technician USA -2002 Licensed Motor Mech NSW MVIC 49593 Current 2015
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Differential Carrier Bearing Question
I have done it by Willys (Spicer) procedure for over half a century, and still have the ordnance and factory tools on hand plus a stock of bearings, Spicer brand shim packs, and NOS Military and CJ differential Ring and Pinions etc. on hand just in case the need arises to do another. I am pretty good at it too.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
Who is online
Users browsing this forum: Google [Bot], maurywhurt, Wolfman and 90 guests